- Видео 171
- Просмотров 530 375
Lex Verkuijl
Добавлен 6 сен 2007
RC Walrus sub, duiktank test met trim
1 Liter eigenbouw zuiger duiktank met stepper motor en Arduino aansturing. 100% vol is 1030 gram, begin trimdeel 955 gram, daarmee 75 gram trimgedeelte.
Просмотров: 62
Видео
RC Walrus sub, test kruisroer aansturing
Просмотров 4714 дней назад
RC Walrus sub, test kruisroer aansturing
F-16 Falcon 1/32 scale as RC submarine, final lichting test
Просмотров 1803 месяца назад
After replacing not reliable and tricky programmable ATtiny with Arduino Pro Micro.
F-16 Falcon 1/32 scale as RC submarine, steering dynamics
Просмотров 1,2 тыс.3 месяца назад
3D Printed elevators, servo throw trimmed and balanced.
F-16 Falcon 1/32 scale as RC submarine, first diving tests
Просмотров 1,1 тыс.3 месяца назад
First diving test at Biddinghuizen, Netherlands. Needs some more balancing en trim, but overall a good testrun.
F-16 Falcon 1/32 scale as RC submarine, flotation test
Просмотров 903 месяца назад
F-16 Falcon 1/32 scale as RC submarine, flotation test
F-16 Falcon 1/32 scale as RC submarine, controll surface test
Просмотров 3814 месяца назад
Final test of control surfaces and steering before second water test. On-off with magnet switch.
V-Twin demo engine, 3D printed,
Просмотров 3,6 тыс.4 месяца назад
Fully 3D printed V-Twin engine for demonstration purposes. Combustion strokes are simulated with RGB LED's as sprakplugs. Airflow in and out is also simulater with blue and red LED's. Crankshaft is driven bij a stepper motor. This motor and all LED's are driven by two Arduino Nano's.
F-16 Falcon 1/32 scale as RC submarine, lighting test
Просмотров 4334 месяца назад
F-16 Falcon 1/32 scale as RC submarine, lighting test
F-16 Falcon 1/32 scale as RC submarine, jet testrun
Просмотров 2 тыс.4 месяца назад
Testruns to test the power of the jet, and basic balance in the model.
F-16 Falcon 1/32 scale as RC submarine, test ATtiny85 light efects
Просмотров 3284 месяца назад
Testing ATtiny85 for lighting effects. From right to left: position lighting, strobe on tail, afterburner respond to near full throttle, interior/exterior effect lighting on/off with switch.
F-16 Falcon 1/32 scale as RC submarine, test afterburner
Просмотров 4755 месяцев назад
F-16 Falcon 1/32 scale as RC submarine, test afterburner
Duo-proefvaart van de nieuwe Clubbootjes / Kinderbootjes van Vaargroep Flevoland.
Просмотров 71Год назад
Hier in de volwassenen stand met volle kracht vooruit beschikbaar.
Autonimous Arduino boat hunted by Smit Noorwegen
Просмотров 149Год назад
And the winner is .... wait for the end!
1:16 Leopard 2A6 build, test stabilization gun and turret
Просмотров 450Год назад
1:16 Leopard 2A6 build, test stabilization gun and turret
1:16 Leopard 2A6 build, first test firing sequence
Просмотров 771Год назад
1:16 Leopard 2A6 build, first test firing sequence
1:16 Leopard 2A6 build, turret stabilization test
Просмотров 2,9 тыс.Год назад
1:16 Leopard 2A6 build, turret stabilization test
1:16 Leopard 2A6 build, stepper rotation test
Просмотров 444Год назад
1:16 Leopard 2A6 build, stepper rotation test
152VO 'Johnny Walker Red Label' VX-543 testrun at optimal trim
Просмотров 1722 года назад
152VO 'Johnny Walker Red Label' VX-543 testrun at optimal trim
152VO DeSliva 'JW Red Label' function test
Просмотров 1452 года назад
152VO DeSliva 'JW Red Label' function test
RC Candela 7 Hydrofoil, second testrun, successfull
Просмотров 5992 года назад
RC Candela 7 Hydrofoil, second testrun, successfull
RC Candela 7 Hydrofoil, foil adjustment, improved speed and throw.
Просмотров 4452 года назад
RC Candela 7 Hydrofoil, foil adjustment, improved speed and throw.
RC Candela 7 Hydrofoil, first testrun on the water
Просмотров 4152 года назад
RC Candela 7 Hydrofoil, first testrun on the water
RC Candela 7 Hydrofoil, final test Flightcomputer and mechanics
Просмотров 6102 года назад
RC Candela 7 Hydrofoil, final test Flightcomputer and mechanics
RC Candela 7 Hydrofoil, test front foil adjusting mechanism
Просмотров 1,1 тыс.2 года назад
RC Candela 7 Hydrofoil, test front foil adjusting mechanism
RC Candela 7 Hydrofoil, steering and mechanics test
Просмотров 6442 года назад
RC Candela 7 Hydrofoil, steering and mechanics test
RC Candela 7 Hydrofoil, synchronous SLA + FDM printing
Просмотров 1572 года назад
RC Candela 7 Hydrofoil, synchronous SLA FDM printing
Not to be that guy but that's not a 4 stroke v twin
It is Don't try to be smart when u dont know that the opposite of your statement is true😂
What is the energy efficiency? How to calculate for this one can you please share the math ?
lekker man
the 2 stroke sounded like 1.9 tdi xD love it
wow, do you have the reference of your solenoid ?
Bonjour Où est-ce que je pourrai avoir ces pièces pour la stabilisation ? Merci de votre réponse
Wow Comment avez vous pu réaliser cela?
very nice! also i hope u changed your smoke alarm batteries :)
Is it a model? Is it art? This is both!
i want a small one of these i can put in my pc and control it via fan speed/header
This is a cool design. I have always liked the F16, the sports car of the fighter world, and I like building strange subs. I hope you can do another video showing a banked turn. Congratulations on a good job.
Next question; is the motor running wet? Brushless? What make? KV?
The motor is brushless, runs in the dry (o-ring seal on the impeller shaft) 4200kv on single cel lipo. Make I don't know , it's a 1106 outrunner.
Where is the intake for the jet pump? I thought it would be the same scoop as the jet engine, under the cockpit, but your servios mechanism looks like it would be in the way.
It is the same scoop, there is room for water to flow to the rear in de thicker parts of the wings, or actualy in the fuselage. It flows left an right of the original jet engine so to speak.
did you waterproof the servos and electronics?
No, those are in a watertight tube and will stay dry. It's a built like a mini RC submarine.
Spot on, if you ask me.
Was that scratch a build? My dream as a kid was to build a hovercraft. There was a film before VHS or digital video on hovercraft development that I checked out for a grade school presentation. On the film there was a tethered control line hovercraft demonstrated. Being one who dreams more than he does I have built neither yet. Good job.
Are you sure that's not a top secret Su-75 shot over the Black Sea. Now special aircraft submarine operation.
It's great. Have you uploaded the 3D file on a website so you can replicate it? It would be interesting to build it with my secondary school students.
not the real one! you need to link the front and back springs to each other
Wederom weer een kunstwerk! Prachtig
Hi there could you advise what all the rudder parts are and where I can also get them. I plan to make a bait boat using fleet scale 1/96 river class fibreglass hull. First boat build and I am impressed with your setup. Thanks
Yes I can, the rudders are made out off aftermarket universal RC boat rudders in aprox. the same saze as the Deans Marine set. They have been cut to make the flap. Hinges and controll pin are made with brass rod and tubing. You can't buy them as these are in this size as far as I know.
@@lverkuijl thank you very much. My next question is this. I have had a look at the motors you used however they are now discontinued as your build is now 7 years ago. Could you recommend motors for me that spin up like the ones you have in the video. Also the shrouds for the props would you mind letting me know what they are aswell. Thanks
@@Poonslaya Any motor 500 to 700 KV will do. The smooth running is not in the motor but in the ESC. Use car ESC's with forward-reverse, with no break function, of where you can switch to direct forward-reverse. XC-10A ESC's have proven to be good in conjuction with the programmer card. Set to direct forward-reverse, and low start power. Search AliExpress on "XC-10a".
Thank you for your input. I am only concerned about the motors not being powerful enough they need to be able to go in the sea and seal with some surf I have seen 1900kv out runners I may go for them and then do as you say regarding the esc
that's so cool
This is really creative! I hope you will become and Engineer 1 day! ❤
Interesting
Interesting concept. Never thought I’d see a fighter jet as a submarine. Just a quick thought through. Wouldn’t the horizontal stabilators (elevators) be good to have as they could act as the “dive planes” that most (if not all) modern military submarines have? You could control the dive and ascent angle easier with the “dive planes/stabilators”.
This was only a test for the self designed and resin printed jet drive, to see if it has enough thrust and will work propperly. That it already went down was just a bonus ;-) Offcourse the horizontal stabilizers will be added to act as diving- and roll planes later on.
@@lverkuijl ok cool! Looking forward to seeing the finished product!
Nice!
Man, i love this, grew up racing DeSilva's! Any links to the plans or where to buy?
Hello Donrusnak, good to hear from someone who raced the real boats! Plans are available through www.152VO.de for only a small donation to the Community.
Thank you so much, I'm very impressed with the 152VO community of racing, not just the runabouts, but all the hydro's too, and in all technicalities, especially alkys, German and Italian motors (and Japan had a good run) were the best and the best hydroplane racing in the world is by your fellow country mates! But you guys never really adopted the runabouts like here in the states
Beautiful work on the DeSilva! Raced DeSilva's for many years and hoping to build a K style rc in the future
What voltage are you using? Bc i cant find these stepper motors for 7.4 volts...
I want to make one. Can i contact you plz
4 stroke sounds crazy
Lex, that is awesome stuff. The gun sound and muzzle flesh rock.❤❤❤ One question, did you replace the HL electronics or did you plug everything on the HL board? Would be so nice to get some deeper insights. Do have a built blog?
Is it possible to buy the files?
so good
add some weight to the gun in the turret , bc its to heavy at the front , it would less wiggle and would be smoother
A coisa que eu mais gostei é que daria pra ter ligado as bobinas uma vez por volta que daria mais potencia igual um motor 2 tempos mais voce fez questao de ligar cada bobina de acordo com o tempo de ignicao de cada cilindro e isso fez toda diferenca no som do motor meus parabens
Holla , very Fast !!! I like . 👍
This a great engine and i love it.
Hunted by Smit Noorwegen, not the Admiral Vladimirsky? 😀
super leuk👍👍
That's great, I want to buy it!
Das beste was ich in rc Welt gesehen habe
Definitely needed in Ukrain.
absolutely amazing project. it would be very helpful if you provide the timing code and stk files?? cheers from india!!!
toppie
toppie
toppie
hey love the project and how it has turned out, just have one question as im currently working on a small engine project of my own, is there any chance i could get my hands on the code you are using for the engine timing as it may be suitable for the pneumatic engine im making?
You are welcome to try. If you send me your mail adres I wil send it to you. But comments are in Dutch, as are several variables. Hope you can cope with that .. ;-)
@Lex Verkuijl Thank you so much and yes thats fine I should be able to work with that and yes but for some reason youtube wont allow me to comment my email as it keeps removing the comment after 30 seconds xD
@@marcustrust9449 try writing it "my dot name at provider dot com" , see what happens ... 😀
@@lverkuijl ive tried everything and it aint workin are you on any other platforms i could send it to you on?
Very well done 👏
Very good design and craftsmanship, like it so much. Did you test it on water?